The Foundation of Plumbing Skills for Bathtub Installation

Get Offer

Just how do you really feel when it comes to How to Install a Bathtub?


How to Install a Bathtub
Setting up a tub isn't specifically brain surgery, however it does require strong plumbing, woodworking, and often, tiling skills. Changing an old tub with a new one is additionally a moderately difficult task. If the old bathtub is readily accessible, the job can relocate speedily; if you need to open up a wall to eliminate the old tub and also place the brand-new bathtub, the job is a lot harder. In either situation, the project is within a residence handyman's skills, although you will need a helper to leave the old bathtub and also set in the new one. See to it you have qualified yourself for the work and also are comfortable trying it. Rather than working with a service provider to take over a halfway-completed task, it is far better to consider utilizing one before you begin. Possibilities are you might need an expert plumber to make tube connections.
This write-up will certainly help you mount a brand-new bath tub in your washroom if you have actually currently purchased a brand-new tub and also don't need to change the setup of your previous water supply pipelines.
Your tools and product checklist should consist of the following:
  • New Bathtub

  • Hammer

  • Pipe Wrenches

  • Prybar

  • Safety Glasses

  • Degree

  • Pliers

  • Flexible Wrench

  • Putty Blade

  • Screwdriver

  • Cold Knife

  • Tape Measure

  • Pipeline Caps


  • Removing Old Touches


    If you require to change old faucets with new ones as a part of your installment, after that the first thing you ought to do is disconnect the water supply. After doing so, turn on the taps to drain any type of water remaining in the system. The process of removing the existing faucets can be rather bothersome because of the restricted accessibility that is usually the situation.
    Utilize a container wrench (crowsfoot spanner) or a tap device to reverse the nut that links the supply pipelines to the faucets. Have a towel all set for the staying water that will certainly come from the pipes. Once the supply pipes have actually been eliminated, utilize the very same device to loosen the nut that holds the taps onto the bath/basin. You will need to quit the solitary taps from turning throughout this procedure. Once the taps have been eliminated, the holes in the bath/basin will have to be cleaned of any type of old securing substance.
    Prior to moving on to fit the new taps, compare the pipe connections on the old faucets to the brand-new faucets. If the old faucets are longer than the brand-new taps, then a shank adapter is required for the brand-new faucets to fit.

    Suitable New Taps


    If the tails of the new taps are plastic, then you will need a plastic adapter to avoid damage to the thread. One end of the port fits on the plastic tail of the faucet as well as the other end provides a link to the current supply pipes.
    If you need to fit a monobloc, then you will require minimizing couplers, which attaches the 10mm pipe of the monobloc to the conventional 15mm supply pipeline.
    Next, place the tap in the placing hole in the bath/basin guaranteeing that the washing machines remain in place between the tap as well as the sink. Protect the faucet in position with the supplier provided backnut. Once the tap is securely in place, the supply pipelines can be attached to the tails of the faucets. The faucets can either be linked by using corrugated copper piping or with normal tap adapters. The previous type ought to be linked to the tap ends initially, tightening up only by hand. The supply pipelines can later on be connected to the various other end. Tighten up both ends with a spanner after both ends have actually been connected.

    Mounting the Bath tub


    Using the two wood boards under its feet, put the tub in the needed setting. The wood boards are useful in equally spreading the weight of the bathtub over the area of the boards instead of concentrating all the weight onto four little factors.
    The next objective is to make certain that the tub is leveled all round. This can be achieved by inspecting the level as well as changing the feet on the bath tub until the spirit level reviews level.
    To set up taps, fit the bottom of the furthest flexible tap connector to the appropriate supply pipe by making a compression sign up with; after that do the exact same for the other tap.
    Activate the water and also inspect all joints and brand-new pipework for leakages and also tighten them if necessary. Fill up the bathtub as well as likewise inspect the overflow electrical outlet and also the typical outlet for leakages.
    Ultimately, fix the bath paneling as explained in the manufacturer's user's manual. Tiling as well as sealing around the bathtub ought to wait until the bath tub has actually been used a minimum of when as this will settle it right into its final setting.

    Preparing for the Installment


    First of all, the sustaining frame supplied with the bath should be fitted (if required) according to the producer's directions. Next, fit the taps or mixer to the bathtub. When suitable the faucet block, it is important to make sure that if the faucet features a plastic washing machine, it is fitted between the bath and also the faucets. On a plastic bath, it is also reasonable to fit a supporting plate under the faucets system to avoid strain on the bath tub.
    Fit the versatile faucet ports to the bottom of the two taps making use of 2 nuts as well as olives (occasionally provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the electrical outlet with the hole in the bathroom. Make use of the nut provided by the supplier to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipeline.
    Next, fit the end of the versatile overflow pipe to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which should be fitted inside the bath. See to it you make use of all of the supplied washing machines.
    Connect the trap to the bottom of the waste outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Connect all-time low of the overflow tube in a comparable manner.The bath should currently be ready to be fitted in its last setting.

    Tiling Around the Bathtub


    In the location where the bath fulfills the ceramic tile, it is required to secure the joins with a silicone rubber caulking. This is essential as the installation can move sufficient to crack a stiff seal, causing the water to pass through the wall between the bathroom and the tiling, causing complications with moisture and also possible leaks to the ceiling below.
    You can select from a selection of coloured sealers to blend in your fixtures and installations. They are offered in tubes and cartridges, as well as are capable of sealing gaps up to a width of 3mm (1/8 inch). If you have a bigger void to fill, you can fill it with twists of drenched paper or soft rope. Remember to constantly fill up the bath tub with water before sealing, to enable the activity experienced when the bathtub is in use. The sealer can fracture relatively early if you do not consider this activity before sealing.
    Conversely, ceramic coving or quadrant ceramic tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are additionally easily readily available on the market. It is a good idea to fit the tiles utilizing waterproof or water resistant sticky and grout.

    A Step-by-Step Guide to Installing a Bathtub


    Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.



    But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.



    This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.


    Remove the Existing Bathtub


    To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.



    The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.


    Choose the Right Bathtub


    The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.


    Install the Plumbing and Ledger Board


    You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.



    Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.


    Install the Bathtub


    When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.



    Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.



    If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.


    Hook up the Plumbing


    Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.


    Install the Bathtub Surround


    A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.



    Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.



    If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.



    If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

    https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/


    How to Install a Bathtub: Install an Acrylic Tub and Tub Surround

    I recently found that blog posting about Installing A Bathtub while doing a search on the web. You should take a moment to promote this content if you enjoyed reading it. We value reading our article about How to Install a Bathtub Yourself.


    Your solution? Just a ring.

    Leave a Reply

    Your email address will not be published. Required fields are marked *